The Problems These Tools Actually Solve
Practical decision guides for chief engineers, superintendents and fleet managers - method comparisons, cost drivers and compliance, with no sales gloss. Grouped by the job you're doing.
Prepare & Protect
Choosing the right method, tool and coating before the crew arrives. Shop surface prep →
Water Blasting vs Mechanical Scaling
Cost per m², MARPOL runoff, flash rust and access - how to choose between the two methods.
Read the guide →Choosing the Right Surface-Prep Tool
Match scaler, grinder or stripper to the substrate, coating and access on the job.
Open the selector →Marine Coating Application
Airless spraying on board, done right - equipment, tips and technique for a durable finish.
Read the guide →Hand-Arm Vibration Prevention
HAVS exposure, trigger times and how low-vibration tools keep crews within limits.
Read the guide →Dust Control for Lead Paint
Why leaded coating dust is H class, what on-tool extraction buys you, and what it does not cover.
Read the guide →ATEX Cleaning & Prep
Working safely with prep and cleaning equipment in hazardous, explosive-atmosphere zones.
Read the guide →Hot Work Permits & Zone 1 Descaling
What an ATEX Category 2 certificate removes, what stays with the site operator, and where beryllium copper is the wrong specification.
Read the guide →Deck Descaling: What One Operator Can Do
The machine is rated at 30 m²/hr; vibration limits cap one operator at about 180 m² a day. Plan the rota, not just the rate.
Read the guide →How Long Can You Safely Use a Needle Scaler?
Under two minutes on a 3BPG, 3 h 39 min on a VL303, at the worse grip. The trigger-time arithmetic, and the secondary-grip figures only the manuals carry.
Read the guide →Scaling Hammer or Needle Scaler?
Open plate or welds, and why the SF1 hammer is a 31-minute tool once you measure the front hand.
Read the guide →Stripping Floor Coverings Before a Refit
Vinyl, lino and carpet tile at 20 m² an hour, and why one operator reaches the vibration action value after 23 minutes.
Read the guide →Cleaning a Cargo Hold Between Cargoes
Wash-down reach, descaling rates, vibration limits, and where MARPOL Annex V actually lets the wash water go.
Read the guide →Move & Handle Fluid
Spec the right pump, power source and running cost the first time. Shop pumps & fluid →
Choosing a Marine Pump
Match pump type to fluid, flow and duty - AODD, electric or specialist transfer.
Read the guide →Electric vs Air-Operated Pumps at Sea
Energy, air demand and total cost of ownership - when to switch from air to electric.
Read the guide →All Graco Guides
The full set of Graco pump, coating and fluid-handling decision guides in one place.
Browse Graco guides →Prove & Inspect
Turning watertight integrity and steel condition into documented, defensible evidence. Shop inspection & testing →
Ultrasonic Testing Aboard Ship
What ultrasonic testing checks and how to use the instruments for repeatable results.
Read the guide →Hatch Cover Leaks & Wet-Cargo Claims
Why quantified ultrasonic testing beats the hose test - and protects you from claims.
Read the guide →Choosing Access for Inspection at Height
Scaffolding, rope access, drone or inspection pole - the trade-offs for close-up work.
Read the guide →How the ALTUM Pole System Works
Building the right visual / UTM / EMAT setup for the tank, silo, hull or pipe rack.
Read the guide →ALTUM Applications
Where inspection poles earn their keep - tanks, silos, hulls, pipe racks and cranes.
Explore applications →Detect, Fix & Comply
Catching invisible costs and regulatory exposure before they become fuel bills or fines. Shop leak detection →
How an Acoustic Imaging Camera Works
Detection modes, models and how to choose the right acoustic camera for the fault.
Read the guide →What Compressed-Air Leaks Cost a Ship
And how an acoustic camera finds them in minutes - with an on-page cost calculator.
Read the guide →The EU Methane Regulation & LDAR
What the move to mandatory leak detection and repair means for gas carriers.
Read the guide →Tell Us What You Need
For a specific product, build your quote on the brand page. Not sure which tool fits? Describe the job here and we'll spec it across the range.
Enquiry Sent!
Thank you. Your enquiry is on its way to the SepcoTech team, and we'll respond within one business day with the right equipment, pricing and availability.